N4PY Icom Control Program Version 2.00 Personal Computer This program is now a 32 bit program. Your personal computer is an integral part of the Icom radio transceiver. The minimum system requirements for your PC to operate Icom radio are a 486 processor running Windows 95. The Icom performs best when running on Windows 95/98/ME/NT/2000/XP or Vista. It will work ok on a minimum system with a 486 processor running Windows 95. Screen resolution of at least 800 X 600 is recommended. Also, in order for this program to pick up frequency, mode, and filter changes performed directly on the radio, "CIV Transceive" must to turned on in the radio. The parameter "CIV with IC-735" must be turned off for this program to work properly. PC to Icom radio Serial Connection Connect a 9 pin serial port cable between the Icom radio serial interface and an available COM port on your PC. When you start the Icom radio control program for the first time you need to tell the program which COM port the radio will be using and what Icom radio you are using. The Icom radio control program looks for the radio on COM 1 by default and assumes a 756PRO at 19200 baud. If needed, choose the appropriate COM port, speed, and radio under the INTERFACE section of the SETTINGS panel. It is also possible to use a USB to SERIAL PORT adapter to operate the radio over a USB port. Please refer to the adapter documentation for information on using a USB port as a Serial Port. Some USB adapters do not work very well and others work great. The one most people are using is from www.keyspan.com. The single port model is USA-19HS at $39.95 and the 4 port model is USA-49WLC at $140.00. If you are using a CT-17 and change radios, it is necessary to "reboot" the CT-17 much in the same way you reboot your computer. Unplug the 9-15V DC power source for 10 seconds, then reconnect. This is necessary for proper CT-17 operation. If you do not have a CT-17 or any other CIV level converter, you have two other choices: 1. Buy a 3rd party converter for $25 to $100: http://k1nu.home.comcast.net/k1nu/Products/ http://www.cssincorp.com/prod-cable.htm http://home.att.net/~n8st/icom.html http://www.microham.com/USB%20interfaces.html http://home.comcast.net/~n4vas/wsb/html/view.cgi-home.html-.html http://n9zle.tripod.com/cable.htm (warning -- this is a tripod-hosted site; don't go here without a firewall!) http://hosenose.com/detail.asp?product_id=LCU-3 (by W1GEE -- recent traffic indicates problems when used with IC765 or IC781) You'll find reviews of the above products at http://www.eham.net/reviews/products/53 2. Build one yourself This is a fun project you can do for less than $10 if you don't get too fancy with the packaging. Radio Shack has everything you need, as does Digikey and other mail order houses. The circuit I use was published by Nigel KG7SG in the 7/92 QST, and can be found in http://www.qsl.net/civ_commander/interface.jpg ; like many others, it derives its power from the serial port's modem control signals DTR and RTS. This is fine, as long as you configure the program to assert DTR. See the "Interface" section for how to do this. Alternatively, you can power the circuit from an external source of +12VDC. Ekki DF4OR has this and some other circuits on his site at http://www.plicht.de/ekki/civ/civ-p2.html , An excellent example of a MAX232-based design done correctly can be found in http://www.seed-solutions.com/gregordy/Amateur%20Radio/Experimentation/C IVInterface.htm . Basic Operation Turn on the Icom radio using the front panel switch. You must wait until the Icom radio is fully operating. The Icom radio must always be turned on first before the program is started. Start the N4PY Icom Control program. The control program should connect to the Icom radio. If needed you may change the selected serial port, baud rate, and radio type in the INTERFACE section of the SETTINGS screen. When using the Icom radio with this control program, do not attempt to use the controls on the Icom radio other than the main frequency knob, mode changes, or filter settings. If you use any other controls on the radio, the program will get out of step with the radio. Mouse Wheel Frequency tuning can be done using the mouse wheel as a tuning knob. The "FAST TUNING MULT" defined in "preferences2" is used as a multiplier for mouse wheel tuning. The tuning step size for the mouse wheel is the selected tuning step size multiplied by the FAST TUNING MULT. Remote Operation Some people enjoy running their equipment remotely. This can easily be done with this program, an audio program such as skype, and a remote access program such as VNC. See www.skype.com for obtaining skype. See www.vnc.com for obtaining VNC. Control Panel Buttons Special Right Click on Mode Button for IC-7800 All the receive mode buttons (AM, LSB, USB, CW, FM, PSK, RTTY) have a special function if "DUAL" receive is turned on. If you right click the mode button, they will send the mode, default filter, and default AGC to the VFO B receiver instead of the VFO A receiver. DUAL This button is only there for the 756PRO, 756PROII, and 7800. It controls the dual receive function. If this button is off, the sub receiver will always be muted. With this button on, both the main and sub receivers will be heard. Also, if this button is off, no data will be sent to the sub receiver until DUAL is turned on. On the IC-7800, if DUAL is on, the left headphone has the main receiver audio and the right headphone has the sub-receiver audio. With DUAL off, both the left and right headphone have the main receiver audio. Right clicking the "DUAL" button will turn on "A=B Frequency Tracking" This mode is indicated with a "DIV" displayed just above the DUAL button. With this mode on, VFO B will automatically follow VFO A in frequency. To turn off this mode, left click on the "DUAL" button. The purpose of this mode is for diversity reception from two receivers at the same time. For true diversity reception, the two receivers must have separate antennas. Please note that if "DUAL" is off, all updates to the sub receiver will be saved and not actually sent until "DUAL" is switched on. M Sliders This button is just for the IC-7800. It is only visible when DUAL is on. It is used to toggle the NR slider, NB slider, SQ slider, and RF slider functions between VFO A (main receiver) and VFO B (sub-receiver). When set for the main receiver, this button is labelled "M Sliders". When set for the sub-receiver, this button is labelled "S Sliders" and the 4 sliders changed by this button are then labelled in lower case to show they are now for the sub-receiver. ManMD This button controls whether or not filter and step information automatically change when a new mode is selected. With this button off, when a new mode is selected, a new filter and step will automatically change according to the mode. With this button on, only the mode will change when a new mode is selected. AM Clicking this button will put the main receiver in AM mode. Also, while in AM Mode, the filter button operation is different for the 756PROII, 756PROIII, 746PRO, 7700, and 7800. See the filter button section for more information. LSB Clicking this button will put the main receiver in LSB mode. USB Clicking this button will put the main receiver in USB mode. CW Left clicking this button will put the main receiver in CW mode. Right clicking this button (not available on the IC-756, IC-781, or IC-775) will put the main receiver in CWR mode. An interesting side effect of this mode is you can tell when you are tuned directly onto a CW signal by swapping back and forth between CW and CWR mode. If the pitch of the signal does not change, you are perfectly tuned to the signal. The 746Pro, 756ProII, 756ProII, 7700, and 7800 have a SSB/CW sync tuning feature. This feature must be turned off in the radio menus for this program to work properly. FM Clicking this button will put the main receiver in FM mode. PSK Clicking this button will put the main receiver in PSK mode for the 7700 and 7800 and all put other radios in USB mode. Right clicking this button will put the 7700 and 7800 in PSK-R mode and all other radios in LSB mode. RTTY Clicking this button will put the main receiver in RTTY mode. Right clicking this button (not available on the IC756, IC775, or IC-781) will put the main receiver in RTTY-R mode. If your radio does not have RTTY mode, then you will get LSB for RTTY mode and USB for RTTY-R mode. Sto SP This button stores the frequency, mode, and filter in a temporary memory for later retrieval. Rcl SP This button retrieves the values of frequency, mode, and filter, last saved with the "Sto SP" button. STORE STORE opens the Store Memory window and prompts you for station data. You can also add a PBT value to the saved memory. If you edit the memory window, you can add "PBT=" text to specify a PBT value to be set when the memory is recalled. For example, if you want a PBT value of 1000 hertz, anywhere in the "Notes" box add the following text: PBT=1000 For a minus 1000 hertz PBT add the following: PBT=-1000 Make sure not to have any spaces on either side of the "=". RECALL RECALL brings up the Recall Memory window and allows you to select stations. Scan Clicking the "Scan" key will cause the stored memory file to be scanned one frequency at a time, beginning at the current entry. The time spent on each memory is called the dwell time. The dwell time is specified in the preferences window. It must be between 1 and 99 seconds. The default dwell time is 2 seconds. All the memories in the loaded memory file will be scanned. When it gets to the last entry, it will start over at the first memory of the file. You will most likely make special memory files to use this scan feature. You can stop the memory scan by clicking again on the "Scan" button. If you add the word "skip" in lower case anywhere in the "notes" section of a memory, the memory will be skipped during the scan function. The memory scan will be stopped if you transmit while the scan is in progress. You can configure an automatic resume time. See the "Preferences4" section. VFO A Left clicking this button will cause the main VFO A frequency to go down by one step amount. Right clicking this button will cause the main VFO A frequency to go up one step amount. VFO B Left clicking this button will cause the alternate VFO B frequency to go down by one step amount. Right clicking this button will cause the alternate VFO B frequency to go up one step amount. FAST A Left clicking this button will cause the main VFO A frequency to go down by one step amount times the "Fast Tuning Mult". Right clicking this button will cause the main VFO A frequency to go up by one step amount times the "Fast Tuning Mult" amount. See "Fast Tuning Mult" in "Preferences2" below. FAST B Left clicking this button will cause the alternate VFO B frequency to go down by one step amount times the "Fast Tuning Mult". Right clicking this button will cause the alternate VFO B frequency to go up by one step amount times the "Fast Tuning Mult" amount. See "Fast Tuning Mult" in "Preferences2" below. FILTER A Left clicking this button will cause the main VFO A filter to go to the next wider filter. Right clicking this button will cause the main VFO A filter to go to the next narrower filter. FILTER B Left clicking this button will cause the alternate VFO B filter to go to the next wider filter. Right clicking this button will cause the alternate VFO B filter to go to the next narrower filter. The VFO B filter setting in displayed in the black area just to the right of the S meter. Here, there are three green indicators to show VFO B mode at the top, then VFO B filter just below mode, and finally VFO B step just below filter. LO CUT Left clicking this button will cause the next lower locut passband step to be selected. Right clicking this button has exactly the opposite effect. This button is useful when QRM appears on the low side of the passband. It allows the low side of the passband to be tuned while keeping the high side of the passband constant. The numeric button directly below the LO CUT button indicates how many steps the low cutoff frequency has moved. You can reset the low cutoff to zero by left clicking this numeric key. HI CUT Left clicking this button will cause the next lower hicut passband step to be selected. Right clicking this button has exactly the opposite effect. This button is useful when QRM appears on the high side of the passband. It allows the high side of the passband to be tuned while keeping the low side of the passband constant. The numeric button directly below the HI CUT button indicates how many steps the high cutoff frequency has moved. You can reset the high cutoff to zero by left clicking this numeric key. PBT Clicking this button on enables pass band tuning for the VFO A receiver. Dragging the scale to the right of the button controls the amount of PBT used. You can right click on the PBT scale to zero it. This control actually moves LO CUT and HI CUT together. LO CUT, HI CUT, and PBT are all closely related. The ranghe of PBT is + or - 1280. The 1280 scale is a relative value that is related to the filter selected for how much movement. This value is 10 times the step value for LO CUT or HI CUT. RIT Clicking this button on enables RIT for the VFO A receiver. Dragging the scale to the right of the button controls the amount of RIT used. You can right click on the RIT scale to zero it. Because Icom receivers do not have computer commands for RIT, this control actuall uses SPLIT and VFO B to operate. RIT can only be used when SPLIT is off and DUAL is off. XIT Clicking this button on enables XIT for the VFO A receiver. Dragging the scale to the right of the button controls the amount of XIT used. You can right click on the XIT scale to zero it. The XIT shares the same drag window as RIT. Because Icom receivers do not have computer commands for XIT, this control actually uses SPLIT and VFO B to operate. XIT can only be used when SPLIT is off and DUAL is off. A / B Clicking this button causes the VFO A and VFO B contents to be swapped. This includes frequency, mode, filter, AGC, LOCK status, and antenna setting. A = B Clicking this button causes the contents of VFO A to be copied into VFO B. This includes frequency, mode, filter, and AGC setting. XFC Clicking this button causes the VFO A and VFO B contents to be swapped if SPLIT is on. This allows the transmit frequency to be checked for activity. SPLIT Clicking this button causes the transmit frequency to shift from the VFO A frequency to the VFO B frequency. LOCK Clicking this button causes VFO A to be locked so that it does not change in frequency. FAST, MED, SLOW These buttons set the AGC speed. They are not available on the IC-756 IC-775, or IC-781. For the IC-7800, if "DUAL" is turned on, you can right click to set the AGC rate for the sub-receiver. Additionally, the IC-7800 and IC-7700 have a "Man" button for manual AGC using AGCVR and the "AG" slider. Re-Initialize Button This button is there is overcome an Icom shortcoming. If any pot is turned on the Icom radio while under program control, all the radio values return to there pot settings. This causes the program to get out of step with the radio. The "Re-Initialize" button causes the program to resend all its settings to the radio to get the program back in step with the radio. S Meter Button This button is only available on the IC-7700, IC-7800, IC-746PRO, IC-756PROIII, and IC-703. It allows the meter display for transmit to be toggled between S meter, power meter, SWR meter, speech compression meter, and ALC meter. In receive, the meter always shows S meter reading. Step Buttons These buttons set the frequency step size according to their value. They are user definable in the "Steps" window of the "settings" menu. Left clicking these buttons changes the VFO A step size. Right clicking these buttons changes the VFO B step size. Band Buttons These buttons are band register buttons. They return you to the last frequency and mode you were using on the appropriate band section. The column labelled "CW" is for the normal "CW" section of that band. Clicking these buttons will return you to the last frequency and mode you were using when in this section of the band. The column labelled "SSB" will return you to the last frequency and mode you were using when in this section of the band. The "SWL" column will return you to the last frequency and mode you were using when in this band. The "GEN" band button is a general band register that gets used if the frequency is not in any other band. The band buttons save the frequency, mode, filter, and antenna setting for each band. Also, you can access the ham band buttons with the function keys. Shift F1 to Shift F9 corresponds to the 160 to 10 meter SSB band buttons and Ctrl F1 to Ctrl F9 corresponds to the 160 to 10 meter CW band buttons. The "60" button under SSB, is a special button. In order to handle the unique requirements of this band, this button has a special click feature. Once you are on the band, you can toggle through the 5 band channels by left clicking to go down one channel or right clicking to go up one channel. Note that when going to the 60 meter band your power output will be lowered to 50 watts if it was more than this. When you leave this band, your previous settings will be restored. AMTN The AMTN (AMP TUNE) button is to make tuning an amplifier easier. When you click the "AMTN" button, several steps happen automatically. They are 1) The current mode and frequency is save in the scratch pad memory. 2) The frequency is moved up 5 kHz. 3) CW mode is set. 4) A wide filter is selected. 5) The Step rate is set to 1 kHz. 6) The griffin tuning knob is set to ALC to control power. 7) The Icom radio power level is set to the previous saved value for this band and mode. While the "AMP TN" button is "RED", you should first make sure the frequency is clear. If it is not, tune to a clear frequency with the mouse by clicking the radio panel knob. Once a clear frequency is found, key your rig with your PTT or CW key and tune your amplifier. Use the remote tuning knob to set the Icom radio output power to correct drive level. When the AMP is tuned, click the "AMP TN" to exit this mode. The frequency, mode, and step will be restored to original values. The Icom radio power output value will be saved and used anytime "AMP TN" is again clicked. This value is kept separate by band and mode. Try this function out. It is a real time saver. The more you use it, the more you will like it. There is also a "pulse tune" method when using Amp Tune. This feature is enabled by setting "PTT Amp Tune Pulse" check box in the "preferences3" window of the "settings" menu. When "AmTn" is on, clicking the "PTT" button will cause a pulsing action to help tune an amplifier in a 50 percent duty cycle instead of 100 percent. TUNE The power when the "TUNE" button is clicked is remembered. When you click "TUNE", set the power to what you want the tune power to be with the TX slider. When you click "TUNE" off, the power will be restored to the previous value. The next time you click "TUNE", it will remember the tune power value and set it to this value. Try it, it may save your finals! This option may be overridden with the "No Tune Save" option described in the "Preferences3" section. ID The ID button is to activate a 10 minute ID timer to assist in meeting the 10 minute FCC ID requirement. Clicking this button causes it to turn blue and start a 9 minute timer (The FCC requirement is 10 minutes, this gives you 1 minute to ID). When this timer expires, a sound is emitted and the button flashes between red and blue. After 10 seconds, the button goes back to blue. To turn the timer off, click the button again and it will go black, indicating the timer is now off. There is an option in "Preferences3" called "Auto Cw ID". Setting this check box on, will cause the ID timer to send your call sign in CW each time the timer expires if you have transmitted during the 10 minute interval. The call will be sent at a fixed speed of 20 words per minute. You must be in either LSB or USB mode, split must be off, and the CW keyboard keyer must be off for this to work. If you right click the ID button, it will send out the CW ID immediately. Transmit Disable This key is used to enable and disable the transmitter. If the button red, the transmitter is set to 0 power output. For the 7700, 7800, 746Pro, 756ProII, and 756ProIII, it is labelled "XmtD". For all other radios, it is labelled "Xmit Disable". DM This button is only on the 7700, 7800, 746Pro, 756ProII, and 756ProIII. It controls going into and out of datamode. Data mode is also automatically turned on when going into PSK mode and automatically turned off when leaving PSK mode. You can disable the automatic switching of this mode by turning on the option "Manual Data Mode" located in the "Preferences3" window of the settings menu. Call This button brings up the call sign window. In order to use this feature, you must have the BuckMaster CDROM installed. Once you have installed the BuckMaster database on your hard drive, you can set the "HamCall Drive Letter or Path" in the "Preferences" window to "c:\ham0\" without the quotes. This will allow calls to be looked up without the BuckMaster CDROM in its drive. Speech This button turns the speech processor and off and on. When the speech processor is turned on, you will see the word "Sp xxx", where xxx is the level of speech processing, near the main frequency. The level of speech processing is set with a slider in the SSB settings menu. It has a range of 0 to 9 with 0 being no processing and 9 being maximum processing. SSB Transmit Filter Bandwidth For the 756Pro, 756ProII, 756ProIII, 746Pro, IC-7700, and IC-7800, there are transmit filter settings of wide, medium, and narrow, in the SSB settings menu. Main Display Panel The main display area contains information about A and B VFO's, tuning steps, AGC selection and Local/UTC time. The Larger of the frequency displays is VFO-A; VFO-B the smaller. Mode Selection Select the mode for the current VFO using the mode buttons. To set the transmit mode in split mode select A/B, set the mode and press A/B again. In Simplex the current VFO's mode will be both the receive and transmit mode. PTT The PTT button provides manual PTT control. With Manual PTT control you can place the Icom radio into transmit mode from the radio panel. This is equivalent to pushing the PTT control on a microphone connected to the front panel. Vox Toggle VOX operation ON and OFF. The button text will change color whenever VOX is turned ON. This button is not available on the IC-756, IC-775, or the IC-781. Mon The mon button allows you to hear your transmit audio. Use it when adjusting microphone or audio input levels. This function is not available on the IC-756, IC-775, or IC-781. Mute Used to temporarily silence the received audio. NBlk This button turns the noise blanker on and off. For the IC-7700 and IC-7800, see the "NB Slider" description. This button is not available on the IC-756, IC-775, or the IC-781. NR Slider This slider sets the noise reduction level. It is labelled "NR". For the IC-7800, if DUAL is on and the "M SLIDERS" button has been changed to "S SLIDERS", this slider is labelled "nr" and then controls the noise reduction level for the sub-receiver. The label for this slider is also a button to turn its function on and off. NB Slider This slider is only on the IC-7700 and IC-7800. It sets the noise blanker level. It is labelled "NB". For the 7800, if DUAL is on and the "M SLIDERS" button has been changed to "S SLIDERS", this slider is labelled "nb" and then controls the noise blanker level for the sub-receiver. The label for this slider is also a button to turn its function on and off. AF Slider This slider is only on the IC-7700 and IC-7800. It sets the APF (audio peak filter) frequency. It is labelled "AF". For the 7800, if DUAL is on and the "M SLIDERS" button has been changed to "S SLIDERS", this slider is labelled "af" and then controls the APF frequency for the sub-receiver. NO Slider This slider is on the IC-7700, IC-7800, 746PRO, 756PRO, 756PROII, and 756PROIII. It sets the manual notch frequency. It is labelled "NO". The label for this slider is also a button to turn the manual notch on and off. Additionally, for the IC-7800, if DUAL is on and the "M SLIDERS" button has been changed to "S SLIDERS", this slider is labelled "no" and then controls the manual notch frequency for the sub-receiver. If "S Sliders" is selected, this label button will turn manual notch on and off for the sub-receiver. AG Slider This slider is only on the IC-7700 and IC-7800. It sets the AGCVR decay rate. It is labelled "AG". For the 7800, if DUAL is on and the "M SLIDERS" button has been changed to "S SLIDERS", this slider is labelled "ag" and then controls the AGCVR decay rate for the sub-receiver. Squelch This slider is labelled "SQ". It controls the squelch setting of the VFO A receiver. For the IC-7800, if DUAL is on and the "M SLIDERS" button has been changed to "S SLIDERS", this slider is labelled "sq" and then controls the squelch level for the sub-receiver. VSC For the 7700, 7800 and 746Pro, VSC can be toggled on and off with the "SQ" label button. VSC stands for "voice activated squelch" and is only available on these two radios. Rf Gain This slider is labelled "RF". It controls the RF gain level of the VFO A receiver. For the IC-7800, if DUAL is on and the "M SLIDERS" button has been changed to "S SLIDERS", this slider is labelled "rf" and then controls the RF gain level for the sub-receiver. Volume VFOA This slider is labelled "VA". It controls the volume for the main receiver. Sub-Receiver Balance Control This slider is labelled "BL" and is only available on the 756PRO and 756PROII. It controls the volume balance between the main and sub receiver. It is only operational when DUAL is on. Sub-Receiver Volume Control This slider is labelled "VB" and is only available on the 7800. It controls the volume of the sub receiver. It is only operational when DUAL is on. Attn The Attn button activates the RF attenuator. This button is not available on the IC-756, IC-775, or IC-781. PreAmp The PreAmp button activates the preamp. This button is not available on the IC-756. Filter Buttons For the 706MKII, 718, 756, 703, 746, 736, and 738 there are 3 filter buttons. Select between normal filter, wide filter, and narrow filter depending on mode and optional filters installed. For the 781 amd 775 there are 2 filter buttons. Select between normal filter, wide filter, or narrow filter depending on mode and optional filters installed. For the 756PRO, there are 3 filter buttons. They select filter 1, 2, or 3 according to your filter definitions in the 756PRO. For the 756PROIII, 756PROII, 746PRO, 7000, 7700, and 7800, the radio panel provides 12 buttons for quick access to the most often used filters. Each of these 12 buttons can be programmed with your choice of filters. To see the filter options right-click on any filter. Any of the 41 filter choices may be assigned to any filter button. For RTTY mode, you cannot use a filter wider than 2700 hertz. If you have the RTTY filter turned on for RTTY operation, then in RTTY mode changing the filter will have no effect. For AM mode with the 756PROII, 756PROII, and 746PRO only, the filter operation is very different. The top left filter button selects the 9 kHz AM filter, the top middle button selects the 6 kHz AM filter, and the top right button selects the 3 kHz AM filter. For the 7700 and 7800 in AM mode, all AM filters from 10 kHz to 2 kHz are selectable and programmable on any of the 12 filter buttons. When AM mode is selected on the 7700 and 7800, the 12 filter buttons change their assignments to the AM filter assignments. Additionally, for the 7700 and 7800, if the selected filter is less than 5800 hertz, the 6 kHz roofing filter is automatically selected. If the selected filter is 5800 hertz or greater, the 15 kHz filter is automatically selected. Auto Notch The "ANotch" button turns auto notch on and off. For the IC-7800, if DUAL is on, right clicking this button turns the auto notch on and off for the sub-receiver. Cw Break-in The "Bk-In" button sets the break-in type for CW mode. It toggles between "Bk-In" which is break-in off, "BSemi" which is semi-break in, and "BFull" which is full break-in. You can control the delay for semi-breakin with the "CW Brk" slider in the "CW Settings" window. This button is not available on the IC-756, IC-775, or IC-781. APF This button is only for the IC-7700 and IC-7800, It controls the APF width. Tha values are off, 320, 160, and 80 hertz. For the 7800, if DUAL is on, right clicking this button turns controls the APF width on the sub-receiver. TPF This button is only for the IC-7700 and IC-7800, It turns the TPF function on and off. For the 7800, if DUAL is on, right clicking this button turns TPF on and off for the sub-receiver. Ant 1 This button toggles between antenna 1 and antenna 2. It's value is remembered by band. For the IC-7700 and IC-7800, this value runs from "Ant 1" to "Ant 4". If you have "Ant 4" defined in the IC-7700 and IC-7800 as the receive only antenna, then the "Ant 4" button position cannot and should not be set from the program. Also, on the IC-7800, you can right click this button to change the antenna for the sub-receiver. Rx Ant This button toggles the receive only antenna on and off. Its value is remembered by band. You can right click this button to set the receive only antenna for the sub-receiver. This button is only on the IC-7700 and IC-7800. Tuner On This button is only available on the 7700 and 7800. It engages the internal tuner and starts a tune cycle. Tuner Off This button is only available on the 7700 and 7800. It turns the internal tuner off and bypasses the tuner. Special right click on "Split" key Right clicking on the "split" key is used as an automatic FM repeater split function. A repeater offset is automatically set in VFO B and "split" is turned on when you right click on the "split" key and you are in an FM repeater band and in FM mode. The split offsets are calculated according to receive frequency as follows: 29.6 to 29.7 MHz - Down 100 kHz 53 to 54 MHz - Down 1 MHz 144.9 to 147 MHz - Down 600 kHz 147 to 148 MHz - Up 600 kHz Please note the the 746Pro DUPLEX feature must be turned off for this program to work properly. Tuning Selections When setting an "F" key on the remote pod is set to tuning selections, it will toggle between VFOA, VFOB, PBT, RIT, ALC, VOL, and RFG. VOL is for volume. Also, each key can be defined to expressly set one of the tuning knob functions. In addition to the functions that were already there you can directly define each function key to set the remote tuning knob to go to VFOA, VFOB, PBT, RIT, ALC, VOL, or RFG. This is done on the remote tuning pod configuration box. You can also make one of the function keys be a "PTT" key by selecting the "PTT" entry. There also is a "SPOT" entry. When this is selected, that function key will turn on the CW spotting tone when pressed and turn it off when released. There is also a "RF Gain" entry. When this is selected, the remote tuning knob will control the RF gain setting. Also, see the "Remote Pod Keyboard Definition" section. There are sliders on the main control panel for Transmit Power (TX), and Keyer Speed (KS). The keyer speed slider on the CW settings panel is a coarse adjustment. It has a range of 40 wpm. The KS slider on the front panel is a fine adjustment. It has a range of 15 wpm. The intended use is for you to set the speed on the CW panel one time to set the general range you want. When you do this, you should first set the front panel in the middle and then use the CW panel setting to get the middle of the range you want. You then use the KS slider on the front panel as a fine adjustment of 15 wpm of the coarse range set from the CW panel. This allows the setting of keyer speed to not be touchy. In addition, if the keyer is enabled, the keyer speed is digitally displayed above the keyer slider on the front panel. You can also change the keyer speed one word per minute at a time. If you left click the "KS" above the "KS" slider you will go down one word per minute. If you right click the "KS", you will go up one word per minute in keyer speed. The upper of the two front panel offset drag control is for PBT. The tuning rate of both these drag control may be user configured. The lower of the two front panel offset drag controls is for RIT and XIT. This controls a single offset in hertz that may be applied to RIT or XIT depending on which is turned on. This is similar to the implementation of the offset function in the OMNI VI. This allows you while listening to a DX station, to tune in the station he is working with the RIT control, and then switch to XIT to actually work the DX station. Note that RIT and XIT only apply to VFO A. Frequency Slider Bar The Frequency Slider displays a coarse view of the band. The displayed band width of the bar will depend on the selected tuning steps and the setting of "Variable Frequency Scale" in "Preferences3". The radio can be tuned using the Slider. Click and hold the left mouse button on the Slider Bar display and drag left or right. The frequency display will show the change and the radio will follow. Double click within the Slider Bar display to jump to a new frequency. S Meter There is an S meter compensation value that you can define to calibrate your S meter. See "S METER COMP" in the "Preferences4" section. Using the Spectrum Display The Spectrum Display or Sweep Window provides the operator with the ability to quickly scan the radio bands and produce a visual representation of station activity. Several user-selectable settings are available to control the width of the sweep, sweep center frequency and display features. This function is not available on the IC-756, IC-775, or IC-781. Sweep Result Display While the radio is sweeping through the selected frequency range the display will change to show each new point as it is processed. When the sweep is complete the radio will return to normal operation and the result window will keep the last data displayed until a new sweep is performed or the program is restarted. The sweep result window provides several types of information. The left and right hand boundaries indicate the start and stop points for the sweep. The range is determined by the range setting. The vertical scale provides a relative comparison between different signals. The higher the point the bigger the signal. The display may be user selected as LOG or LINEAR. Display Format The sweep display format window control provides selections for displaying the sweep results in either LOG or LINEAR format. Display Style Sample points in the sweep display window can be displayed as solid lines or as dotted lines using this control. A change to this selection will be reflected immediately in the display if the sweep window currently contains a sweep result. Sweep Pulse Width This box is used to select how many pixels wide each plotted sweep pulse is. Wide pulses yield a fast sweep time but low resolution. Narrow pulses yield high resolution but slow sweep times. The first selection is called "Default Pulse Width" and lets the program decide the width. This box has no effect if "High Resolution" is checked since that size uses a fixed 1 pixel width size. Sweep Center Frequency The operator may choose to let the sweep center frequency be the same as the receiver tuned frequency with the TRACK_RECEIVER option or select MANUAL and enter the center frequency in the box provided. The MANUAL operation allows for the sweep of frequencies removed from where the radio is tuned. There is also an option called "Band Center". This option puts the center of the band you are currently tuned to in the center of the sweep window and automatically adjusts the width to match the band segment. Sweep Range The amount of spectrum covered in each sweep can be set using the Sweep Range control. The default range is 300 kHz. Starting and Stopping a Sweep Pressing the SWEEP button will begin the sweep acquisition of data for the sweep display. The process involves tuning the receiver to each frequency and getting a signal strength reading. The display is updated with each new point as it is gathered. To stop a sweep in progress press STOP at any time. There is a selection for spectrum sweep called "MaxHold". When this is selected, only signals that are stronger than what is already displayed at that location will be changed. This allows the presence of strong signals that come and go to remain on the sweep screen. There is a selection for spectrum sweep called "Integrate". When this is selected, the sweep display is integrated over several passes with the formula: Displayed Value = Previous Value - Previous Value/4 + New Value/4 Thanks to KH7T for this formula. There is also a "High Resolution" check box on the spectrum sweep. Selecting it causes the sweep display to show a large increase in resolution. However, the sweep speed is significantly slowed down when this is on. You can decide between speed and resolution with this setting. When using the IC-7800, the sweep uses the sub-receiver, leaving the main receiver available for general operation. Do not transmit while sweep is running. There is a "Wide Sweep" check box on the spectrum sweep. Selecting it causes the sweep display width to double. A program restart is required for the sweep panel to change size. Main Window Title The VFO A frequency is displayed on the main window title. This allows the frequency to be seen when the radio control panel window is minimized. This is very useful as it allows you to tune with the remote tuning knob and see the frequency while minimized. License Class You can define your license class and have your transmit privileges displayed on the frequency scale. You define your license class in the "preferences" section of the settings menu. You can also decide to have your transmitter follow your license class with a check box in this same area. When you define your license class, the background of the frequency scale will be blue for CW and digital mode only operation, green for phone operation, and burgundy for operation not allowed. If you select to have your transmitter follow your license class selection, transmit will be blocked when your transmit frequency is tuned to a non-authorized frequency for your class. When you select your license class, the last selection is called "foreign". This selection is for foreign countries that have different operating privileges than the U.S. It allows you to define your operating privileges via an ASCII file called "foreign.dat". Each line of this file defines a band segment you are authorized to operate in. There are 3 entries in each line. The first entry should be either "cw" or "phone". If "cw" is specified, it means the band is restricted to CW or digital modes. If "phone" is specified, it means the band has no bandwidth restrictions. The second entry defines the starting frequency for the band segment in MHz. The third entry defines the band segment end in MHz. There is a limit of 29 entries for the entire "foreign.dat" file. The supplied "foreign.dat" is an example of how one would define a file for a foreign country that had privileges identical to a U.S. general class license. There are also entries in the Icom.ini file to control the point that the band button segments for the 160, 80, 40, 20, 15, and 10 meter bands switch from CW to SSB. There is also one entry to control the switchover point between 40 SSB and the 41 meter SWL band. These entries are as follows with defaults as shown: 160 meter line=1.840 80 meter line=3.750 40 meter line=7.150 4041 meter line=7.300 20 meter line=14.150 15 meter line=21.200 10 meter line=28.300 You can change these values to the appropriate value for your countries usage in these bands. There is also a "SSBRTTY.DAT" file that can be used to define the frequencies you want RTTY or SSB mode selected automatically when doing direct frequency entry. This file can have up to 28 lines for RTTY and 28 lines for SSB. Each line for RTTY must start with "RTTY", and each line for SSB must start with "SSB". Follow the mode name with a comma, followed by the starting frequency in mhz, followed by the ending frequency for the mode in mhz. This file can be edited with notepad or any ASCII text editor. Examining the file will show the exact format. The USA SSB and CW band limits are built into the program. This file is used to override those values. CW Keyboard Keyer There is a CW keyboard keyer. It is turned on with the "Alt-K" key sequence. When the keyboard keyer is enabled, the letters "Cw Kb" will appear just to the left of the "SPLIT" key. Pressing "Alt-K" again will turn off the keyboard keyer. Some buttons may cause the keyboard focus to move from the main radio panel causing the keyboard keys to not send CW. When this happens, either click on the radio front panel with the mouse or do Alt-K twice to restore the keyboard focus. Using the CW Keyboard will force the Icom internal keyer to be enabled. If you accidently press the "enter" key while using the CW keyboard, it will put you into "direct frequency entry" mode. Press the "Esc" key to get back to CW keyboard mode or key in a frequency and press "enter" again. The keyed characters will not be sent until a full word is typed. The space bar is necessary to define the end of a word. This allows words to be transmitted smoothly and also gives you an opportunity to correct a keying error before the word is transmitted. This full word feature can be turned off by un-checking the check box labelled "Transmit full words only" located in the "CW Keyboard" window. The F12 key will toggle the CW Keyboard buffer between pause and transmitting. This key will allow you to type ahead while you are receiving. If the buffer is stopped, the "Cw Kb" will appear RED. If the buffer is transmitting, it will be black. The speed and weight of the keyboard keyer are controlled with CW keyer speed and weight controls. Typing at the keyboard will cause the appropriate character to be transmitted in CW. Special CW characters are as follows: BT is sent with the "-". SK is sent with the "$". AR is sent with the "+". KN is sent with the "^". di-dah-di-dah for traffic handling is sent with the "*". The "escape" key will immediately end sending and empty the CW internal keyboard buffer. There are two CW weight controls. They are a "Dah Wght" and a "Dit Wght" control. The value of each weight setting appears as a number from 0.8 to 1.70 at the bottom of each weight slider. The length of a dah is computed as the length of a space times 3 times the dah weight setting. The length of a dit is computed as the length of a space times the dit weight setting. The length of a space is fixed at the keyer speed setting. Theoretical perfect 3 to 1 spacing occurs at a dah weight setting of 1.00 and a dit weight setting of 1.00. These weight controls are used on both the CW keyboard keyer and the internal paddle keyer. Additionally, there is a slider marked "Btwn Char". This slider controls a weighting of the between character time. The normal between character time is multiplied by the value of this slider. The range is 0.5 to 4.0. This is used to either lengthen or shorten the time between sending characters. A value of 1.00 results is normal spacing for the selected speed. Obviously, this slider is only for the CW Keyboard Keyer and not for the paddle keyer. There is a CW Keyboard window for showing the contents of the CW keyboard buffer. This window is visible when the CW Keyboard is turned on. It may be hidden by clicking the "X" in the upper right hand corner of the window. You can make the window visible again by doing Alt-K twice. The keyboard buffer is 500 characters long. There are 5 memories that can be used with the keyboard keyer. The memories are loaded with the edit boxes on the "CW Keyboard" window. The memories are transmitted by pressing F1 for memory 1, F2 for memory 2, F3 for memory 3, F4 for memory 4, and F5 for memory 5. There are also 5 mouse buttons at the bottom of the radio panel labelled "M1" to "M5" to transmit the memories. There are also 5 CW Memory Tag edit boxes. These edit boxes, located in the "CW Keyboard" window, will change the labels on the M1 through M5 memory buttons. You can use these tags to help remember what is in each memory. They are limited to 3 characters. The special character "#" followed by a number from 1 to 5 can be placed in a memory to cause the contents of the memory number to be sent in place of the "#" character. This is useful to increase the size of a memory for a longer message. The special character " (double quote) can be placed at the beginning of a memory to send a file instead of the text in the memory. When you start a memory with a " (double quote), you directly follow the " with the name of the file you want to send text from. The internal CW keyboard buffer is limited to 511 characters so the file cannot be larger than 511 characters. You can never be more than 511 characters ahead of what is being transmitted. The file must be built with an ascii text editor such as notepad. If you build the file with notepad, the actual name of the file will have a ".txt" added to it. The basic name itself must be 8 characters or less and not have spaces or special characyers in it. The file must be located in the c:\n4pyic folder or wherever you have the program installed. The special character "%" followed by a number from 1 to 9 can be placed at the end of a memory to cause a delayed repeat of the memory. The number 1 to 9 is the delay in seconds before the memory is resent. When the repeat function is active, a capital "R" will show in the keyboard display buffer. The repeat function is cancelled when any new character is added to the keyboard buffer or a new memory is selected with the F keys. K1EL Keyer The program has full support for the K1EL Winkey keyer version 4 or later. Information on getting this keyer can be found at www.k1el.com. There is a check box in the CW settings window labelled "K1EL Keyer". Checking this box causes all the CW setting controls to change to the K1EL settings controls. Using this keyer allows the keying to be much smoother, especially for Windows XP, NT, and 2000. The controls are as follows: Additionally, if you are using the Winkey 2 keyer, the 4 buttons on top of the keyer will run the program memories 1 to 4. "Key Spd" - This slider sets the minimum range for the K1EL speed pot. The speed pot low end is set to this value and the high end is set to this value plus 15. Thus the range of the speed pot is always 15 wpm. Note that the actual keying speed of the K1EL is always set with the speed pot on the keyer itself. The "KS" slider on the program front panel will show the current speed but the "KS" slider cannot be used to change the K1EL keyer speed. If you do not have a speed pot on your keyer, check the "No Speed Pot" box and the KS slider will control the keyer speed. "Wgt" - This slider controls the keyer weighting. A value of 50 is no weighting. "Ptt Lead" - This slider controls the lead time the PTT line is energized before keying begins. The values are in 10 millisecond increments. This is useful to control an amplifier to ensure the amplifier relay comes up before RF is applied. "Ptt Tail" - This slider controls how long PTT stays energized after keying stops. The value is in 10 millisecond increments. "Key Comp" - This slider controls the amount of keying compensation applied to all keying elements. It is in milliseconds and adds a fixed amount of milliseconds to all character elements. "Dit Dah" - This slider controls the dit/dah ratio and allows you to change it from the standard 1:3 ratio. A value of 50 corresponds to the normal 1:3 ratio. The range of the control is 33 to 66, with 33 being a 1:2 ratio and 66 being a 1:4 ratio. "AutoSpace" - This check box enables or disables the keyer's autospace function. "CT Spacing" - This check box enables or disables the keyer's contest spacing option. "Use PTT Pin 5" - Turn this check box on if you want to use pin 5 of the keyer output for PTT. The default is to use it. "No Speed Pot" - Turn this check box on if you do not have or do not wish to use the speed pot on your WinKey keyer. "Reverse Paddle" - This check box allows you to use a paddle with the dit and dah connections reversed. "Iambic B" - This list box selects between Iambic B, Iambic A, Ultimatic, and Bug operation. "COM setting box" - This box allows you to define the correct comport the K1EL keyer is connected to. Consult the K1EL manual for more explanation of these controls. If you have the CW Keyboard turned on, you will get character echos from the paddle in the CW Keyboard window. This will show you what you the last 20 characters you have sent with the paddles. Using direct entry from the keyboard Keyboard frequency entry is always active while on the main radio panel unless the CW keyboard is active. If the CW keyboard is active, you should first press the "enter" key to get into direct frequency mode. Entry works by simply typing in the frequency. You may also click inside the frequency display to edit the frequency as in a normal text box. If you enter a frequency that is above 1000, the program assumes you have entered the frequency in kHz. If the value is below 1000, the program assumes you have entered the frequency in MHz. If you begin the entry with a ".", the program assumes you are only entering the kHz portion of the current MHz you are tuned to. To enter a frequency below 1 MHz, start the entry with a "0" followed by the "." and then the kHz value. To enter 680 kHz, key in "0.680". Griffin Pod Keyboard Definition The keys on the keyboard numeric pad are programmable. There are four entries in the settings window to define the keys. The entry "Remote Pod" is used to define the three function keys. The entry "Remote Pod 789" is used to define the 7, 8, and 9 keys. The entry "Remote Pod 456" is used to define the 4, 5, and 6 keys. The entry "Remote Pod 123" is used to define the 1, 2, and 3 keys. The entry "Remote Pod P0" is used to define the period key and 0 key. Most of the values you can select are self-explanatory. An entry labelled "5" would be for the "5 key" to define it just for direct frequency entry. An entry labelled "up 5" would be for the "5 key" to define it to turn on split and make VFO B be up 5 from VFO A. The entry marked "Band Bottom" takes you to the bottom of the band. The entry labelled "AccInp Xmit" is a special one for slow-scan TV users. Clicking this button will cause the Icom radio to go into transmit mode, and the monitor audio to come on. Clicking this again, will turn off transmit, and turn off monitor audio. This is extremely useful during slow scan TV sessions when you are changing from sending pictures to SSB to describe them. Also, when in this mode, the main program title adds additional text to note you are transmitting. If you have the pod in RIT tune mode and RIT is on, if you press the pod RIT button again, it will set the RIT value to zero. The entry marked "Up Numeric" causes that key to set "up numeric mode". When you follow this key with a numeric key it sets VFO B equal to VFO A plus the numeric value of the key and then turns on "split". Note that the zero key causes you to go up 10. This allows you have have a "quick split" ability of 1 to 10 kHz without having to use all your numeric key definitions for this feature. The nice part of all this is you do NOT lose direct frequency entry from the remote pod when you define the numeric keys for other things. All you have to do is press the "E" key first, and the pod is then put into numeric mode for direct frequency entry. I leave it up to the creativity of the user to come up with a really nice remote pod key definition. The following example is how I use my remote tuning pod to work a Split DX pileup: I tune the dx station in on VFO A. I soon find out he is listening say up 5. I press the "Up" key on the pod followed by the "5" key. Now VFO B is tuned 5 kHz higher than VFO A. This is a starting point. Next I press the "dual" button I have defined on the pod and I set the pod to tune VFO B only by pressing the pod's VFO B key. I don't need to lock VFO A because the pod is now only tuning VFO B. I also press the pod's "SPLIT" key at this time. Now anytime I tune the pod knob, I am only tuning the DX listening frequency and not the DX transmitting frequency. As soon as I hear the DX transmitting, I press DUAL to turn it off so I don't hear all the callers. When the DX listens to a calling station, I turn dual back on and tune the pod knob to find the caller. If I find the caller, then I call at the next opportunity. Because I am now transmitting right where the DX station was listening, I have a greatly increased probability of getting through. It works pretty well. Pod Function Keys Without a Pod There are over 25 pod functions that can be assigned to keyboard keys. You can get pod functions from the keyboard without having a griffin knob or TenTec remote pod. The pod functions for numeric 6 to 9 can be done with F6 to F9 on the keyboard. The pod function for the zero key can be done with F10. The pod function for F1 can be done with F11. You can also use the numeric 1 to 5 for pod functions 1 to 5 if the CW keyboard is turned off and you have defined that you have a griffin powermate. Additionally, if the CW keyboard is off, F1 to F5 will operate as pod functions for 1 to 5. Please note the F keys only work as pod keys when the griffin powermate option is selected. Preferences2 Menu Window The default filter positions for each mode are defined with numbers from 1 to 12. Number 1 refers to the top left filter button, number 2 refers to the top center button, and so on to number 12 for the bottom right filter button. The default AGC setting for each mode is also defined in this window. The entry labelled "Do Not Use Auto AGC" simply means to not change the AGC setting when going to that mode. The value of the "Fast Tuning Mult" can be set using the "Fast Tuning Mult" edit box in this window. This value controls the amount of step multiplication used when the "FAST A" and "FAST B" buttons are used. The default value is 10. If the step being used is 50 hertz and this has a value of 10, then when the "FAST A" and "FAST B" buttons are used, the step would become 500 hertz. This controls how much tuning speed up is invoked when using these buttons. This value is also used as a multiplier for tuning with the mouse wheel. Preferences3 Menu Window The second decimal point in the displayed frequency can be removed. This is useful is you are doing a lot of cut and paste operations. Use the "Remove Extra Decimal" check box. Setting the "No Tune Save" check box will cause the tune power to always be whatever the ALC power slider is set to. Setting it unchecked will cause it to remember the value last set while tune was in progress. When the "Variable Frequency Scale" check box is checked, the analog frequency scale will vary with the step size. For steps less than 100 hertz, the scale is multiplied by 100. For steps between 100 and 1000 hertz, the scale is multiplied 0by 10. For steps above 1000 hertz, the scale is unchanged. This scale change is primarily for people that do not have the remote tuning pod to aid in dragging the frequency. With this option unchecked, the analog frequency scale is fixed. When the "Manual Data Mode" check box is checked, data mode will not automatically be selected when going into PSK or RTTY. This option is only available for the 7700, 7800, 746Pro, 756ProII, and 756ProIII. The "PTT Amp Tune Pulse" check box causes a "pulse tune" method when using Amp Tune. When "AmTn" is on, clicking the "PTT" button will cause a pulsing action to help tune an amplifier in a 50 percent duty cycle instead of 100 percent. The "Remote Pod PTT Toggle" check box allows the remote pod PTT button to be used as a toggle. With this check box on, pushing the remote pod PTT button will cause the Icom radio to go to transmit. Releasing it will do nothing. Pressing it again will cause transmit to stop. Setting the "PC keeps time in UTC" check box assumes time on your PC is kept in UTC time. Un-checking this box assumes time in your PC is kept in local time. This value is used in displaying local and UTC time in the radio panel. Setting "POLLING (Omni V.9 Only)" check box causes the radio to be periodically polled for frequency and mode. This is only necessary for radios that do not support the CIV Transceive option such as the TenTec Omni V.9. Setting "Using IC-PW1 Amp" causes all frequency commands to be sent using a broadcast address. This is to allow the IC-PW1 solid state amplifier to automatically follow the transceiver. The "Auto Memory File Entry Select" check box, when on, causes an entry in the memory file that corresponds to the current tuned frequency to be automatically selected. This automatic selection only occurs if the memory file has been sorted by frequency. With this check box off, this selection does not occur. The reason for setting this off is a performance reason. Under some circumstances, this automatic selection can slow down tuning of the radio. The option "Frequency Event Timer" is explained in the "Frequency Event Timer" section. Preferences4 Menu Window The "PBT Drag Scale" and "RIT Drag Scale" are used for setting the fine tuning rate of RIT/XIT and PBT. You can set the fine tuning rates to 1, 2, 4, 8, 16, or 32. Changes to these values do not go into effect until the program is restarted. The "Transfer Folder" box is used to set the folder for the Ten-Tec file interface. Some logging programs using the Ten-Tec file interface are not configurable for the location of "pegasus.out" and "pegasus.in". This parameter allows you to specify the folder for these files. Setting TRANSFER FOLDER C:\MYFOLDER would cause the location of the "pegasus.out" and "pegasus.in" files to be in the "c:\MYFOLDER" folder. The default for this parameter is the folder the N4PY control program runs in. The default is in effect if the window shows all blanks. The "High Speed tuning Factor" box causes the tuning rate when the tuning knob is turned at a high rate to be multiplied by this factor's amount. Legal values for this factor are 1 to 100. Use the value of 1 to disable this feature. The "S Meter Compensation" box is an S meter compensation value that you can select to adjust the calibration of your S meter. This value is expressed in + or - dB. Remember each S unit is 6 dB. For example, to make your S meter always read 12 dB lower (2 S uints), you would set the value as follows: S Meter Compensation -12 To make your S meter always read 12 dB higher (2 S units), you would set the value as follows: S Meter Compensation 12 The "Frequency Display Delay" parameter is for users that are running a remote station using PCAnywhere or other remote software. This parameter can be used to slow down the display updates so that the remote program does not get behind on too many screen updates. Normally, you set this to zero, but in some PCAnywhere setups you would set this to 1000 ( 1 second) or so to allow tuning and not have excessive screen updates while tuning. The "S Meter Polling Time" parameter is similar to the "Frequency Display Delay" but determines how often the S meter on the radio is checked from the program. Normally, this is set to 200 (0.2 of a second) but when using PCAnywhere, this may be too fast. A setting of 1000 (1 second) works well with PCAnywhere over a slow remote link. The "Diversity Tuning Delay" parameter is similar to the "Frequency Display Delay" but determines how often the "M=S" command is sent to the radio when diversity receive (righ click on dual) is set. Normally, this is set to 0 but when using PCAnywhere, this may be too fast. A setting of 200 to 400 (.2 second to .4 second) works well with PCAnywhere over a slow remote link. If the "RED Frequency Display on Transmit" check box is on, when transmitting the frequency is displayed in RED. If this box is set off, the frequency is always displayed in yellow. If split is on, the VFO B frequency box will always display the transmit frequency in red as a reminder that split frequency operation is being used. This option can be used on all radios except the IC-706 and the IC-718. The Icom radio "Sweep Delay" setting may be configured. Because the AGC in the Icom radio receiver is not extremely fast even in fast mode, a delay needs to be added when the sweep is running to allow time for the AGC to react to the new frequency as the frequency is swept. The normal value for this parameter is 10 millisecond. You can experiment with increased delays for more sweep resolution. Valid values are 0 to 500. Watch out for the zero setting! The box "Scan resume after transmit time" allows you to configure a scan automatic resume time. If the scan was stopped because the transmitter came on, this value controls how long transmit has to be off before scan comes back on again. A zero value means no automatic scan resume is used. The value of the resume time is in seconds. Frequency Scan Window Selecting this window will show the frequency scan controls. The scan will start at the "Frequency Start" setting. When the radio reaches the "Frequency Stop" setting, it will loop back to the "Frequency Start" setting. The "Frequency Increment" controls how much is added to the scan frequency for each dwell time. The "Dwell Time" setting controls how long the radio remains on each frequency. To start the scan, "click" the "Start Frequency Scan" button". To stop the scan, "click" the "Stop Frequency Scan" button. The scan will not start if a memory scan or spectrum sweep is in progress. The scan will be stopped if the radio goes into transmit mode. You can control the direction of the scan. If the start frequency is less than the stop frequency, the scan will go up in frequency. If the start frequency is greater than the stop frequency, the scan will go down in frequency. Colors Window In order to help out hams with sight difficulties, the color of the button text can be configured. There are three settings to control the text colors of the buttons. Additionally, you can also define the color for local time display and UTC time display. There are 8 standard colors that can be selected. They are BLACK, WHITE, RED, GREEN, BLUE, YELLOW, PURPLE, and CYAN. There are also 2 user definable colors that can be selected with the names COLOR1 and COLOR2. Local Time This entry sets the color of the text for the display of local time. UTC Time This entry sets the color of the text for the display of UTC time. Button Text This entry sets the color of the text for all non-selected buttons. Button Sel Text This entry sets the color of the text for all selected buttons. Special Button Sel Text This entry sets the color of the selected text for the five special buttons LOCK, TUNE, DUAL, AMPTN, and SPLIT. CW Bkgnd This entry sets the color of the background for the CW keyboard window. Settings Bkgnd This entry sets the color of the background for the settings window. CW Text This entry sets the color of the text for the CW keyboard window. To define the user color called COLOR1, three settings are used to specify the amount of red, green, and blue to make up the color. The range for the amount of each color is 0 to 255. Color1 Red This entry controls the amount of red in the Color1 color. Color1 Green This entry controls the amount of green in the Color1 color. Color1 Blue This entry controls the amount of blue in the Color1 color. To define the user color called COLOR2, three settings are used to specify the amount of red, green, and blue to make up the color. The range for the amount of each color is 0 to 255. Color2 Red This entry controls the amount of red in the Color2 color. Color2 Green This entry controls the amount of green in the Color2 color. Color2 Blue This entry controls the amount of blue in the Color2 color. SWL Band Assign Window This window allows the 11 SWL band buttons to be defined to any frequency range you like. If you do not use the SWL bands and prefer to make these buttons be RTTY buttons or if you just want to make these buttons be any band you desire, you can do it here. The first column is labelled "Caption". The 11 edit boxes in this column allow you to name the button text for the SWL band buttons. The second column labelled "Lower Limit", allows you to set the lower frequency limit for the band you are defining. The third column labelled "Upper Limit", allows you to set the upper frequency limit for the band you are defining. Be careful when you set up your band ranges not to have any bands overlap. The first time you go to the new band you have defined, you should set the mode you desire for this band. The button will now remember the frequency, mode, and filter when you return to this band. You can change the column name for the SWL band buttons. This is the box at the bottom labelled "Column Name" in the "SWL Band Assign" window. Call Sign, TopTen Window Your call sign can be displayed on the control panel. You set your call sign in the "Call Sign" box in this window. You can define the color of the text of your call sign on the radio panel. They are BLACK, WHITE, RED, GREEN, BLUE, YELLOW, PURPLE, and CYAN. There are also 2 user definable colors that can be selected with the names COLOR1 and COLOR2. The default is BLACK. You can also define the relative size of the characters by using the "Call Sign Size" box. You can set the relative size from a value of 1 (the default), to a value of 15 (probably too large). For the boxes labelled "TopTen Devices", see the section on using Top Ten devices antenna control near the end of this file. 2 Transverter Window 2m Crystal Correction If you use the Ten-Tec 2 meter transverter, you can get the display to show the frequency very accurately by specifying the amount of error in the transverter crystal frequency. Specify this error in hertz with a plus or minus sign in the edit box. 2M Drive Power Max (0-100) You can specify the maximum amount of ALC drive to the transverter with this parameter. Its range is 0 to 100 with 100 corresponding to 100 watts. Use caution when setting this. 5 watts is the recommended setting which corresponds to a setting of 5. The scale of the TX slider is adjusted so that full scale corresponds to this value. If you are going to use the Icom radio's 20 mw transverter output, set this value to zero. 2M IF This parameter controls the internal IF frequency to the Icom radio will be set at when using the converter. The Ten-Tec transverter uses a 28 MHz IF. This is the default value. If you are using some other transverter that uses a different IF, you can specify it in this edit box. If the "Suppress Transverter Warnings" check box is on, no warnings will be issued when leaving a transverter band. User Configurable Transverters Window There are 5 user configurable transverter setups that the user can setup to work with virtually any transverter. These transverters are in addition to the 6 and 2 meter transverter setups that are built in. These transverters are configured in the "User 1 & 2 TranV" window, the "User 3 & 4 TranV" window, and the "User 5 TranV" window. The transverter must not be in the 1.7 MHz to 30 MHz range (the Icom radio can transmit in this range) and the transverter must tune in the same direction as the IF frequency. That is to say, as you tune the transverter to a higher frequency, the Icom radio IF frequency must also go higher as well. You cannot use an inverting transverter. For each transverter, there are 6 parameters to configure. They are: User N Lower Limit This sets the lower frequency limit for the transverter. It also enables the transverter and makes its band button appear after and program restart. User N Upper Limit This sets the upper frequency limit for the transverter. User N IF This tells the program what frequency to set the Icom radio to at the lower limit of the transverter range. User N Button Text This tells the program what text to display on the band button for this transverter. It is limited to 4 characters. User N Drive Pwr Max (0-100) This sets the maximum drive power the Icom radio will run at to drive the transverter. Its range is 0 to 100. 100 corresponds to 100 watts. 5 is the default which corresponds to 5 watts. Great care should be used in setting this value. The scale of the TX slider is adjusted so that full scale corresponds to this value. If you are going to use the Icom radio's 20 mw transverter output, set this value to zero. User N Crystal Correction You can get the display to show the frequency very accurately by specifying the amount of error in the transverter crystal frequency. Specify this error in hertz with a plus or minus sign in the edit box. The band buttons for these transverters only appear when the particular transverter is configured. The buttons are in the lower right corner of the radio window. Care must be taken when setting up these parameters, as bad values can cause strange problems. RTTY Settings Menu Window When the "Output RTTY Mode is RTTY Label" check box is set, the text for the mode in the pegasus.out file for the RTTY and PSK mode will be as follows RTTY mode "RTTY" RTTY-R mode "RTTYR" PSK mode "PSK" PSK-R mode "PSKR" With this box turned off, the text for the mode in the pegasus.out file for RTTY and PSK modes will be: RTTY mode "LSB" RTTY-R mode "USB" PSK mode "USB" PSK-R mode "LSB" Step Window The "step buttons" are user configurable to any step between 1 and 10000. They are configured in the "step" window of the "settings" menu. The default values for the operating modes can be configured to any step between 1 and 10000. They are also configured on the "step" window of the "settings" menu. Note that in AM mode, if the frequency is in a HAM band, the AM step will be the value specified for SSB step. Also note that MW Step defines the step value for the American AM broadcast band. SSB Settings window In this window are settings for tranmsit filter bandwidth, speech processing, and Mic gain. Also for the IC-7700 and IC-7800, there are roofing filter selections. The roofing filter selections are as follows: Auto Selection - This setting sets the roofing filter as narrow as possible but no narrower than the selected DSP filter. This is normally the optimum setting. 15 khz Fixed - This setting makes the selected roofing filter always be 15 khz. 6 khz Fixed - This setting makes the selected roofing filter always be 6 khz. 3 khz Fixed - This setting makes the selected roofing filter always be 3 khz. Do Not Change - This setting leaves the roofing filters completely unchanged from where they are set. Interface Window This window allows you to configure comport settings and radio type. For any changes in this window to take effect, you must exit and restart the program after you make the change. If you check the box labelled "Get Icom at Start", the program will get the Icom radio frequency, mode, and filter at startup and use these as initial values instead of the last used settings by the program. "Find Baud Rate Automatically While Tuning Radio Directly" If you are having difficulty getting the program and radio to talk with each other, turn this check box on. While the check box is on, slowly tune the radio directly from its tuning knob. In about 20 seconds or less, you should see the program connect to the radio. "Radio Type listbox" Select your Icom radio type here. Your selections are IC-756PRO, IC-756PROII, IC-746, IC-746PRO, IC-706MKIIG, IC-756, IC-718, IC-781, IC-775, IC-7800, IC-GEN, IC-703, IC-7800, IC-756PROIII, IC-7000, IC-736, IC-738, and IC-7700. The IC-GEN setting is for all other Icom radio types and the TenTec Omni VI, Omni V.9, and Paragon II. It allows simple frequency, mode, and filter settings for older radios. The Omni VI default CI-V address is 04. Also the IC-7400 is identical to the IC-746PRO. So for the IC-7400, select IC-746PRO. "CIV Address" Normally you select "Default" for this listbox, but if you have changed the CIV address of your radio, you can define the value here. "BAUD Rate" The best speed to use here is 19200 baud. You can change it to a lower speed if you like. This rate much match the transceiver's baud rate. "WriteLog Multiple Radio Interface" - This feature should only be turned on when using WriteLog and running multiple instances of the N4PY program with each instance controlling a separate radio. This feature allows WriteLog to log each instance of each N4PY program to a separate log file in WriteLog. Each instance is associated with the primary comport number the N4PY program is using. "Use DTR to power serial interface" Only turn this checkbox on if you are using a serial to CIV converter that derives its power from the DTR line. Turning this option on disallows the use of "Use DTR for CW Keying". "Use RTS to power serial interface" Only turn this checkbox on if you are using a serial to CIV converter that derives its power from the RTS line. Turning this option on disallows the use of "Use RTS for CW Keying". "Use DTR for CW Keying" "Use RTS for CW Keying" These boxes tell the program to use DTR or RTS for keying the radio while in CW Mode. One of these two options is required in order for the "Tune" button to work and the CW keyboard to work. The program will operate PTT without this option set because PTT can be controlled with computer commands sent to the radio. This requires a simple interface be added that allows either DTR or RTS to key your radio through a transistor. Many interfaces are available that do this. Below is a simple way to make one. Carefully remove the insulation from the cable to expose the individual wires inside the cable. You need to determine the wire that goes to pin 4 or PIN 7. Pin 4 is the DTR line and Pin 7 is the RTS line. You can use a small pin and an ohm meter to determine this. You also need to find the wire that goes to pin 5. This is ground on the serial cable. Solder the pin 4 (DTR) or pin 7 (RTS) wire the 1000 ohm resistor. Solder the other end of the resistor to the base of the 2N2222 transistor. Solder the pin 5 wire to the emitter of the transistor. Now take the RG-174 coax and solder the center lead of the coax to the collector of the transistor. Solder the shield of coax to the emitter of the transistor. Add a plug on the other end of the coax to plug into your CW key line. This is shown schematically below. serial cable coax center wire -------- to CW Key line / DTR PIN 4 --------1000 ohms---- | 2N2222 OR RTS PIN 7 \ > GND PIN 5 ------------------------|------- coax shield The above will allow DTR or RTS of the serial cable to key the radio. Restore Filters Window This window is only for the IC-746PRO, IC-756PROII, IC-7700, and IC-7800. With the IC-746PRO and IC-756PROII, when the program changes filters, the values for Filter2 change to the last value the program set. This window allows the program to restore the original values for Filter2 at exit time for SSB and CW mode. The other modes are not affected. For the IC-7700 and IC-7800, changing filters from the program causes the values for both Filter2 and Filter3 to change to the last value the program set. This window allows the program to restore the original values for Filter2 and Filter3 at exit time for SSB, CW, RTTY, PSK, and AM modes. User Buttons Window There are 4 user buttons available for the 7700 and 7800 only. These buttons allow you to define commands you can send to the 7700 and 7800. You can change the User Button Text to anything you like to allow you to remember what you have defined for the button. The command is defined in hexadecimal. For example, the command to set Mic input is "1a05003100". The command to set SPDIF input is "1a05003107". There must be an even number of characters in a command for it to be valid. Consult the Icom 7700 and 7800 command set for full definition of these commands. Icom.ini file Parameters for the [OPERATING STATUS] section The value for each parameter below is set to the default value. This is the value you get when the parameter is not defined. The text will indicate what other values are legal. SCALEX=1 SCALEY=1 There are scale factors for the main radio window. You can add lines in the [RADIO WINDOW] section for horizontal and vertical sizing scale factors. For horizontal scaling use SCALEX=1 For vertical scaling use SCALEY=1 The scale factors are used as multipliers of all coordinates in the program. With these values set to 1, the size of the main radio window will be unchanged. To make the window 10% larger in both axis use a value of 1.1 for each scale factor. To make the window 10% smaller, use 0.9 for each scale factor. This is being added for hams that have visual problems seeing the screen and not recommended if you have normal vision. If you make the window scale smaller, some characters may not display properly. Try this at your own risk. PEGASUS COMPORT=NONE This parameter is in the [INTERFACE] section. It can be used to control the radio via a TenTec remote tuning knob connected to a TenTec Pegasus. This feature is only for people that happen to have a TenTec Pegasus with remote tuning knob. It allows the tentec remote tuning pod to control the Icom radio. To enable this feature, you only have to specify the comport the Pegasus is connected to. For example, if you connect the Pegasus to com3 you would change this line to: PEGASUS COMPORT=COM3 This feature only enables the TenTec Pegasus for remote pod usage. No other functions on the Pegasus are available. PTT COMPORT=NONE This parameter is in the [INTERFACE] section. It can be used to control PTT for CW keying using a separate comport. You can use either DTR or RTS to key the radio by selecting one of these two options from the INTERFACE window of the settings menu. For example, if you connect your PTT to com3 you would change this line to: PTT COMPORT=COM3 Frequency Event Timer This option is selected with a check box in "Preferences3". This feature allows you to define frequency events and have the radio go to those frequencies when the time for the event occurs. This is very useful for unattended operation with a receiving radio on the internet. The frequency events are defined in a special file called "events.txt". This file is created the first time you turn this option on with its check box. The file is located in the c:\n4py folder or wherever you have the program installed. Once you have turned on the option the first time, exit the program, and edit the "events.txt" file to create frequency events. Do not edit the file with the program running. The file is column sensitive. Each time must be 2 numeric characters followed by a colon, followed by 2 numeric characters. There should then be one space followed by a frequency expressed in megahertz. The events are defined by the day of the week. There can be up to 24 events for each day of the week. The file has a section for each day of the week and 24 events for each day. You should carefully edit the default lines with the values you want. All the default lines have a time of 00:00 and a frequency of 00.000. These times are in the local time of your computer and not in UTC. The times must be in 24 hour time with a range from 00:00 to 23:59. When program finds a match with the day of the week, hour, and minute, the program will change to the indicated frequency and set the corresponding default mode and filter. Memory File Usage Memories are saved in files that are "RMY" file types. RMY files are binary files and are not editable with an editor. They save all the significant parameters for the station including "split status" and the transmit frequency. If you want to edit an RMY file, you must first export the file. See "Importing and Exporting Files" below. The "File" menu has several entries to control memory file usage. The memory file entries in the "File" menu are as follows: New - Clicking this entry will allow you to start a brand new memory file. If the current memory file has not been saved to disk, you will be asked if you want to save it before the current memory is cleared. Open - Clicking this entry will allow you to open a memory file that has been previously saved. You will be shown all the RMY file types that exist in the program working folder. Close - Clicking this entry will save the current memory file contents to disk and end usage of this memory file. Save - Clicking this entry will save the current memory file contents to disk but still keep the memory contents in memory. This is useful to do just after you add a memory and want the disk to be updated with the new entry. Save As - Clicking this entry will save the current memory file contents to disk but still keep the memory contents in memory. This is useful to do just after you add a memory and want the disk to be updated with the new entry. It also allows you to give the disk file a new file name. Importing and Exporting Files On the file menu, there is an Import and Export. These functions allow the ability to import and export files that are text files. This allows you to export the current memory files as a text file and then add more stations to it. You may get these files from any source and simply combine them by following the file format. Later, you may import this file back into memory and assign an RMY file name to it. The format of the file is straight forward. An entry simply occupies a single line. Each line has ASCII text for the station name, station frequency in MHz, station mode, filter in hertz, country, language and optionally split frequency. Each value is separated by a comma with no extra spaces. Inspection of an existing file will show the format clearly. To export an RMY file, first open the RMY file as follows: 1) Click on "File" 2) Click on "Open" 3) Select the RMY file you wish to open 4) Select OK The above opens and loads the RMY file in memory. To export the RMY file, proceed as follows: 1) Click on "File" 2) Click on "Export" 3) Type in the name you wish for the CDF file 4) Select OK To import a CDF text file, proceed as follows: 1) Click on "File" 2) Select "Import" 3) You should see the files of type CDF. 4) Select the file you wish to import and click OK. If you then want to create an "RMY" file so that when you run the N4PY program next time you can get this file automatically selected, proceed as follows: 1) With the CDF loaded into memory as above, click "File". 2) Select "Save As" 3) Type in the name such as "NEWFILE.RMY" 4) Select OK This will save the data in the RMY format. You can now make this file name the default memory file as follows: 1) Select "File" 2) Select "Open" 3) You should see "NEWFILE.RMY" 4) Select this file as click OK. If you are a member of the ILG database (www.ilgradio.com), you can download an ASCII text version of their data. This is a file called "ilgstext.zip". I have a DOS utility program that can convert this database to a "CDF" file which can then be imported into the Icom radio control program. Send me an email if you would like to have this file converting program. Saving and Restoring Icom Radio Memories On the file menu, there are three entries for saving and restoring the Icom radio memories. They are as follows: Save Icom Memories - Clicking this button will allow you to select a "CDF" file to save the memories in. The memories will be saved in a standard CDF file that can be used later to import files. It takes about 1 minute to save the 99 memories. The Icom radio memories are numbered 1 to 99. Restore Icom Memories - Clicking this button will allow you to select a "CDF" file to restore memories from the file to the Icom radio. Abort Sav/Res Mems - Clicking this button while a "save memory" or "restore memory" operation is underway will abort the save or restore memory operation. For IC-7000, there is a memory bank setting in the "Preferences" window of the settings menu. You can use this to select memory bank A to E for saving or restoring memories or you can set it to "All" to save or restore all Icom radio memories. If the memory bank values are in the CDF file for restore memories, then this value is ignored. There is full support for all memories including split status and 9 character memory names. See the "sam7000.cdf" sample file for the file format. Memories 5 and 7 in bank A are examples of split memories. During the Save and Restore memory operations, the current memory will show as the text on the "Store" below, just to the left of the "Recall" button. Using Top Ten Devices Antenna Control There is an automatic antenna selection feature provided to allow users to use the automatic band decoder provided by Top Ten Devices. This unit allows you to have either an external amplifier or external antenna switch automatically follow the Icom radio frequency settings. This program offers full support for the parallel port with all windows versions. Information on this band decoder can be found at www.qth.com/topten/bdecoder.htm Parallel port 1 is used to control the Top Ten device controller. This is enabled in one of two configurations by going to the "Call Sign, TopTen" window of the "settings" menu. Selecting "TopTen Devices Option 1", causes the bands marked on the Top Ten Devices controller to follow the Icom radio frequency precisely. In option 1, the bands are selected as follows: Frequency < 2 MHz selects band 1 Frequency >=2 MHz and < 4 MHz selects band 2 Frequency >=4 MHz and < 8 MHz selects band 3 Frequency >=8 MHz and < 12 MHz selects band 4 Frequency >=12 MHz and < 16 MHz selects band 5 Frequency >=16 MHz and < 20 MHz selects band 6 Frequency >=20 MHz and < 24 MHz selects band 7 Frequency >=24 MHz and < 26 MHz selects band 8 Frequency >=26 selects band 9 Selecting "TopTen Devices Option 2" causes a unique setup for controlling the device. In option 2, the bands are selected as follows: Frequency < 200 kHz selects band 1 Frequency >=200 kHz and < 30 MHz selects band 2 Frequency >=30 MHz and < 55 MHz selects band 3 Frequency >=55 MHz and < 149 MHz selects band 4 Frequency >=149 MHz selects band 9 When a frequency change is detected, the new band setting is output to the parallel port. The Top Ten Automatic Band Decoder is plugged into this parallel port and responds to the information sent to the port. This program includes drivers for the parallel port so you do not need to do anything to setup the parallel port. LDG Electronics AT-200PC Autotuner Setting the "Enable AT-200PC" check box in the "Transmitter" window of the "settings" menu will cause the memory tuner controls to appear at the lower left side of the radio panel. You must also set the correct comport for the AT-200PC. When using the Jupiter with the AT-200PC, you must be in pegasus emulation mode. The Jupiter cannot be keyed from the program while in front panel mode. The LDG AT-200PC must be at firmware version 1.9 or later for correct operation. See the LDG website for how to upgrade your tuner to this version. When using this tuner, the program will remember the tuner antenna settings by band. In addition, when changing bands with the program band buttons, the last tuner setting for that band will be recalled automatically without transmitting. If for some reason, it is ever necessary to clear out the EEPROM in the LDG tuner, the "Clear Mem" button in the "Transmitter" section of the settings menu can be used for this purpose. This will clear out all tuner memories. This is necessary if you have changed antennas and want to setup new tuner memories. Also, it is recommended that you perform an "Auto Tnr" on each band you will operate. For bands 7 mhz and up, you should do one "Auto Tnr" in the CW portion and another one in the SSB portion for the band you use. For 80 meters, you should do an "Auto Tnr" for at each 100 khz interval. For 160 meters, you should do one at each 50 khz interval for the portion of the band you intend to use. All these "Auto Tnr" operations must be done with the correct antenna selected. Once these "Auto Tnr" functions have been done, it will not be necessary to do them again unless your antennas change. There are 8 buttons. They are: 1) "Auto Tnr" - Left clicking this button will cause the memory tuner to go into auto tune mode. When the tune completes or 20 seconds go by, it will automatically stop. When it completes, the store memory routine will automatically run to save the current settings for the particular memory range you are in. If the "Auto Tnr" button turns red after the tune operation is over, it indicates the tune operation failed and the tune needs to be done again. Also, if the "Auto Tnr" button remains blue, it indicates the program 20 second timer timed out without getting a response from the tuner. If you click the "Sto" button, the program will accept the settings from the failed tune. 2) "Bypass" - Left clicking this button will put the memory tuner into bypass mode, thus removing it from the output circuit. Click the "Rcl Tuner" button to put the tuner back in use. 3) "Ant1" - Left clicking this button will toggle between the tuner's antenna 1 and antenna 2 connection. 4) "Cap" - Left clicking this button will tweak the capacitor setting of the tuner "down" in value. Right clicking this button will tweak the capacitor setting "up" in value. 5) "Ind" - Left clicking this button will tweak the inductor setting of the tuner "down" in value. Right clicking this button will tweak the inductor setting "up" in value. 6) "HiZ" - Left clicking this button will cause to tuner to go to its "Lo Z" or low impedance setting. Left clicking again will cause the tuner to go to its "Hi Z" or high impedance setting. The descriptor on the button indicates the current impedance setting of the tuner. 7) "Sto" - Left clicking this button will cause to memory tuner to save its current settings for this frequency to memory. It is only necessary to use this button if the "touch up" cap and ind buttons have been used. 8) "Rcl Tnr" - Left clicking this button will cause the memory tuner to recall the last settings for this frequency from the tuner's memory. If the SWR is greater than 2.0, the "Auto Tnr" procedure will automatically be started to try and find a better match. If the "Auto Tnr" button turns red after the tune operation is over, it indicates the tune operation failed and the tune needs to be done again. If you click the "Sto" button, the program will accept the settings from the failed tune. There is a tuning paramter in the pegasus.ini file to set the SWR threshold. Look for the line that says: LDG SWR THRESH=50 To change the SWR threshold, change the value to one of the following: 50 = 1.1 51 = 1.3 52 = 1.5 53 = 1.7 This one seems to work the best for me 54 = 2.0 55 = 2.5 56 = 3.0 The default is 53 for 1.7 to 1 threshold. Program Support for the Griffin Technology PowerMate The Griffin Technology PowerMate can be used for tuning the Icom radio. The PowerMate must be configured as follows: RotateRight - SendKey with key value of Alt-G RotateLeft - SendKey with key value of Alt-B Click - SendKey with key value of Alt-I LongClick - SendKey with key value of Alt-Y Example for setting up the Alt-G key in the Griffin Powermate configuration program: The N4PY program must be active while this is done. Enter the correct file in the "Setting" window. This is "icom" for all operating systems. Then follow the procedure below: 1.User Action=rotate right 2.Computer Action=send key 3.Click "Change Key" 4.Checkmark in "Alt" 5.Type letter "g" (ignore upper/lower case. Ignore "Hint"). Do not put checkmark in "Shift". Follow exactly this procedure using the letter "B" for "rotate left", the letter "I" for "click", and the letter "Y" for "long click". Click "Apply Now". Click "OK" Close PowerMate program. Open PowerMate program once again. Set "Sensitivity" at or near "fast. Click "Apply Now". Click "OK". Your finished. Note: If, when you are using the knob to change frequency and it tends to "run past" after you've stopped turning the knob, lower the sensitivity slightly until it operates properly. The numeric keypad on the keyboard becomes the keys that go along with the PowerMate. If the keys are not reacting properly, you may have to click on the program radio panel to get the keyboard focus to the radio panel. Once the PowerMate is properly setup, you can now configure "Remote Pod 0-3" and "Remote Pod 4-9" to operate from the numeric keypad of the computer keyboard. Pressing the PowerMate knob down quickly will produce a click that the program will interpret as "F1" and follow the setting for "F1". Likewise, pressing the PowerMate knob for a long click will cause an "F2" operation to be performed. There is no operation for the F3 key. Once properly setup, you can use the PowerMate to change frequency, filters, RIT, PBT and many other things. You can still use the numeric keypad for direct frequency entry by pressing the "ENTER" key first. You can purchase the PowerMate by going to www.griffintechnology.com. Diagnostic Tracing There is a check box in the "Preferences" window labelled "Diagnostic Tracing". This is used to gather trace information for Carl to debug a problem. When changing this setting, you have to exit and restart the program for the new setting to take effect. Turning this on causes tracing information to be written to the 3 trace files "comms.txt", "comms2.txt", and "comms3.txt". Only turn this on when you have been asked to by Carl. Hot Keys on the keyboard Increase step size Decrease step size Tune Down Tune Up Fast Tune Down Fast Tune Up Decrease Speaker Volume Increase Speaker Volume <-> Decrease Speaker Volume <+> Increase Speaker Volume A=B A/B AM Mode CW Mode Speech Proc FM Mode Show Message Box with this Menu CW Keyboard Keyer LSB Mode Mute Audio PTT Toggle RTTY Mode Split ATTN USB Mode Quit 0 - 9 Begin Entering Frequency F1 CW Keyboard Keyer Memory 1 F2 CW Keyboard Keyer Memory 2 F3 CW Keyboard Keyer Memory 3 F4 CW Keyboard Keyer Memory 4 F5 CW Keyboard Keyer Memory 5 to SSB Band Buttons to CW Band Buttons For comments and suggestions email to n4py@arrl.net Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635